收藏本站
16-Port, 36V Constant-Current LED Driver
Applications Information
Selecting External Component R SET to Set
LED Output Current
The MAX6971 uses an external resistor, R SET , to set the
LED current for outputs OUT0–OUT15. The minimum
allowed value of R SET is 327.3 Ω , which sets the output
currents to 55mA. The maximum allowed value of R SET
is 5k Ω . The reference value, 360 Ω , sets the output cur-
rents to 50mA. To set a different output current, use the
Overtemperature Cutoff
The MAX6971 contains an internal temperature sensor
that turns off all outputs when the die temperature
exceeds approximately +165°C. The outputs are
enabled again when the die temperature drops below
approximately +140°C. Register contents are not
affected, so when a driver is overdissipating, the exter-
nal symptom is the load LEDs cycling between on and
off as the driver repeatedly overheats and cools, alter-
nately turning the LEDs off and then back on again.
formula:
R SET = 18,000 / I OUT
Power-Supply Considerations
The MAX6971 operates with a chip supply V+, and one
where I OUT is the desired output current in mA.
Computing Power Dissipation
The upper limit for power dissipation (P D ) for the
MAX6971 is determined by the following equation:
P D = (V+ x I+) + (V OUT x DUTY x I OUT x N)
where:
V+ = supply voltage
I+ = operating supply current when sinking I OUT LED
drive current into N outputs
DUTY = PWM duty cycle applied to OE
N = number of MAX6971 outputs driving LEDs at the
same time (maximum is 16)
V OUT = MAX6971 port output voltage when driving load
LED(s)
I OUT = LED drive current programmed by R SET
P D = power dissipation, in mW if currents are in mA
Dissipation example:
I OUT = 20mA, N = 16, DUTY = 1, V OUT = 2V, V+ =
5.25V
P D = (5.25V x 25mA) + (2V x 1 x 20mA x 16) = 0.77W
Thus, for a 24-pin TSSOP package (T JA = 1 / 0.0122 =
+82°C/W from the Absolute Maximum Ratings ), the
maximum allowed ambient temperature T A is given by:
T J(MAX) = T A + (P D x T JA ) = +150°C =
T A + (0.77 x 82°C/W)
so T A = +86°C.
or more LED supplies. Bypass each supply to GND
with a 0.1μF capacitor as close to the MAX6971 as pos-
sible. This is normally adequate for static LED driving.
For multiplex or PWM applications, it is necessary to
add an additional bulk electrolytic capacitor of 4.7μF or
more to each supply for every 4 to 16 MAX6971s. The
necessary capacitance depends on the LED load cur-
rent, PWM switching frequency, and serial-interface
speed. Inadequate V+ decoupling can cause timing
problems, and very noisy LED supplies can affect LED
current regulation.
Chip Information
PROCESS: BiCMOS
_______________________________________________________________________________________
9
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX6974ATL+ IC LED DRIVER LINEAR 40-TQFN
MAX6977AAE+ IC LED DRIVER LINEAR 16-SSOP
MAX6978AUE+ IC LED DVR CONST-CURR 16TSSOP
MAX6979AUG+ IC LED DRIVER LINEAR 24-TSSOP
MAX6983AUG+T IC LED DRIVER LINEAR 24-TSSOP
MAX71020AEUI+ IC ENERGY METER 1PH 28TSSOP
MAX7302ATE+ IC LED DRIVER LINEAR 16-TQFN
MAX7307AUB+T IC LED DRIVER LINEAR 10-UMAX
相关代理商/技术参数
MAX6971AUG-T 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6971EVKIT+ 功能描述:LED 照明开发工具 Evaluation Kit for the MAX6971 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
MAX6972ATJ 制造商:Maxim Integrated Products 功能描述:16-OUTPUT PWM LED DRIVERS FOR MESSA - Rail/Tube
MAX6972ATJ+ 制造商:Maxim Integrated Products 功能描述:LED DRVR 16SEGMENT 3.3V 32TQFN EP - Rail/Tube
MAX6972ATJ+T 制造商:Maxim Integrated Products 功能描述:LED DRVR 16SEGMENT 3.3V 32TQFN EP - Tape and Reel
MAX6972ATJ-T 制造商:Maxim Integrated Products 功能描述:16-OUTPUT PWM LED DRIVERS FOR MESSA - Tape and Reel
MAX6972EVKIT 制造商:Maxim Integrated Products 功能描述:16-OUTPUT PWM LED DRIVERS FOR MESSA - Rail/Tube
MAX6973ATJ 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube